The part number for this key fob is in five fa zero ata to open this key fob your first step is to push the button and release the key. Use the metal key to pry away the back cover.
This will separate the two pieces slightly.
How to change battery in ford key fob 2014. Use a flathead screwdriver to pry out the old battery. Line up the rear cover of the fob over the front half. Insert a new cr2032 3 volt battery in to the socket with the positive + side facing up.
You may also use a coin, butter knife, key or nail file. Press the release switch and slide out the metal key with your fingernail. When ford changed the design of their ford focus flip key, an easy little job became a puzzle.
Pull the key straight out of the slot. Set the key aside in a safe place. Test new key fob battery:
Slide the metal key in the key fob and test the key fob operation. Gently snap together the two pieces of the fob until they are flush. Remove the cover by pushing the buttons on the side of the fob and pulling it off second:
Once you've done that you'll wanna take a small flat head screwdriver inserted into the notch on the side of the key fob. Remove the physical key from the fob and insert your screwdriver in the end that hides the tip of the key and push the tip down. Replace the rubber seal over the front halve of the key fob.
Line up rear cover of fob: Sent from my nexus 7 using tapatalk 2. Install the new battery with the positive (+) symbol facing the back cover.
Turn the key from the off position to the run position (the position right before you actually crank the starter) and then back to the off position seven times. The fob opens two ways one for the key and the other for the battery. Do replace batteries with the size and type specified by the device’s manufacturer.
Just had my 2019 st in today for it’s second service. We’ve seen several of these keys that have been forced open, searching for a way to get to the battery! Slide over the switch to release the backup / emergency metal ignition key.
On the seventh cycle, leave the key in the run position. Ford recommend replacing key fob battery every two years at a cost of £9.95 fitted, i declined sod paying that. The only tool needed to replace the battery is a small flathead screwdriver or a plastic pry bar tool used to pry off the rear cover.
The only item required for the restoration of the fob is a replacement battery. Press button on the key fob to release and flip out the key. The key fob i'm showing you today is compatible with the 2014 through 2015 ford fusion.
The process is brief, taking only minutes to complete. To get to the key press the two points on the side near the key ring at the same time, this will allow the ford cover to be pried off, exposing the key. Line up the back cover of the key fob and gently snap together the two halves.
Turn over the fob and locate the release switch. Remove the battery casing from the key fob. However opening the key is.
Align the back cover on the key fob and press it on. Remove batteries from devices that will be stored for extended periods. Push a new # cr2032 3 volt battery in to the socket with the + positive side facing up towards you.
Do store batteries in a cool, dry place at normal room temperature. Undo the screw using a small flat screwdriver. Remove all used batteries from the device at the same time, then replace them with new batteries of the same size and type.
Now for the battery replacement, i used a pair of needle nose pliers that i inserted in the indent on the side towards the. Test new key fob battery: You will need to use a rhythm here, making each forward and backward motion occur in roughly the same amount of time.
Gently pry apart the two halves of the fob. The part where i'm having problems is where i try to separate the two halves of the fob apart. How do i change my ford focus key battery?
The manual says to twist at a certain area of the fob and then pry the halves apart, but it doesn't seem to work. Here's what you can do to replace the battery in your ford fusion key fob. Note the battery on the back cover.
A small flat head screwdriver 3. Locate the notch on the top edge of the key fob near the unlock and lock buttons. Insert a coin, butter knife or a large flathead screwdriver in to the notch.
Insert new battery + side up: Remove and replace the battery ensuring that insert the battery with the correct polarity. Release the metal key by pushing the silver button on top of the key fob.
This easy to use step by step guide can help you easily repair your key fob to continue usage. Locate a small notch at the side of the key and insert the tip of the flathead screwdriver to pry apart the key fob gently. The first step is to locate the small notch at the bottom corner of the key fob near the red panic alarm button.