The intellifire and intellifire plus use batteries to pilot your gas fireplace during a power outage. An electric spark then lights the pilot light so it can in turn light the burners.
If it is out, you might just need to merely relight it with a match or a lighter.
How to light a gas fireplace with electronic ignition when power is out. If the vent free gas logs or vented gas logs still will not ignite, the most likely culprit is a dirty pilot light, or a pilot light that is not lit. However i have no power coming out of ignition module. When gas logs first come out they had a match lit ignition meaning you turned a knob to let the gas out and then lit it with a match.
With the new ipi systems, that cost is almost entirely eliminated. The traditional method to igniting a fireplace, a match lit ignition system requires the flames be lit manually by holding a matchstick or a long lighter near the burner before opening the gas valve. This type doesn’t use any pilot light at all.
Enter the new electronic ignition systems for your gas fireplace. I have checked for voltage coming in and out of transformer and i have power on both sides. Using a wall switch to turn on a gas fireplace;
Newer generations of gas fireplaces use an electronic ignition system, requiring electricity to start up. Lighting a gas fireplace using the control panel. My electronic ignition gas fireplace will not light.
A gas fireplace with an intermittent pilot ignition (ipi) valve system will remain operational during a power outage. If your power goes out, the milivolt system could be manually turned on to heat your home. If your ignitor is broken, make sure to get your fireplace serviced prior to your next session.
It can be done for one. Most modern gas fireplaces will have an ignitor, and you should use it if you have one. Once you have given any excess gas a chance to dissipate, follow the instructions in your system’s manual to relight the pilot.
But the ipi switch would not consume gas unless you flipped on the wall switch or used the remote. If you have a standing pilot, the gas fireplace will light itself without the need for electricity. With that said, you can always light a gas fireplace by holding the pilot light down and lighting a match.
The second and more common type of electronic ignition system is the hot surface igniter. Generally, intellifire systems require two d cell batteries, and intellifire plus systems require four aa batteries. A gas fireplace uses natural gas, as opposed to wood, to maintain a flame.
Am i right to think the problem is the ignition module? This piece is found on just about any gas appliance as it is the primary ignition source. It's not by any mean a dyi project.
The conversion would not be cheap. Or are there further diagnostics i. A standing pilot light that runs 24/7 will cost you an estimated $.60 per day, depending on the gas prices in your area.
The ipi system would not be able to ignite the pilot light manually based on an electronic ignition switch during a power outage. When the furnace turns on, a valve opens up and allows the gas to flow to the pilot light. Because that system does not use external electricity, the fireplace works if the power goes out.
Batteries should only be used as a power source only in the event of a power outage. That’s just under $20 a month, or $75 per season. To check if it is doing its job just open the vent and look to see if there is a small flame inside.
Electronic ignition fireplaces save you the cost of running a pilot light 24/7, usually about. Chick ignition if gas fireplace will not ignite. The gas control valve and pilot assembly would need to be replaced for one, then you'd need an ignition control module, transformer, and ac power source.
Lighting a gas fire with a key valve. Many models have a battery backup that can be used to light the pilot during a power outage. If the gas smell does not dissipate, close the valve going to the fireplace and call for service.
But the pilot may need to be lit manually on occasion. Many models, such as heatilator gas fireplaces and gas inserts are outfitted with intellifire or intellifire plus ignition systems, which have battery backup systems that can be used to light the pilot during a power outage. You can use your valve to increase or decrease the.
After being sparked by electricity, the. If you smell gas when troubleshooting your ignitor system, wait five minutes before trying to light it again. Then came the safety pilot with a piezo ignition on log set that you pushed a button that created a spark in front of the pilot that heated then the pilot heated a thermocouple to keep the valve open to operate the log set.
Many gas fireplaces and gas inserts are outfitted with intellifire or intellifire plus ignition systems which have battery backup systems that can be used to light the pilot during a power outage. Often, this will involve manually depressing the pilot valve and using an electric ignitor or match to light the pilot. When the furnace shuts off, the valve closes and the pilot light goes out.
This adds up quickly to a few hundred dollars per year.