Removal (without key) use this procedure to remove lock cylinder if key is missing or cylinder is frozen. It will hang loose, and then you can fix it to the correct spot and replace the ignition lock cylinder successfully.
The official method the factory manual tells you to do has already been mentioned;
How to replace ignition switch without key. Simply loosen the tabs to pull out the switch. See appropriate steering columns article in steering. Unbolt its assembly and ignition switch housing that comprises of the lock cylinder.
Remove the screws and pull the switch out. To change the ignition switch on a keyless car, first, remove the ignition switch and then follow the normal steps for changing the ignition switch. A hammer and a large screwdriver or chisel.
I ordered a new ignition switch and keys and now realized i need the key to replace. The following procedure applies to vehicles where the ignition lock is inoperative or lock cylinder cannot be rotated due to broken or missing ignition key and the key number is unknown, or the lock cylinder cap is damaged and. Unbolt the ignition switch housing and assembly, which contains the lock cylinder.
Press and hold the door lock switch to the unlock position. Remove the indicator and wipers switches. Screwdriver image by hazel proudlove from fotolia.com.
How to change ignition switch without key. Grab ya a drill bit the a bit smaller than the pin and drill it out. Insert the ignition key a third time leaving the key in the ignition lock cylinder.
Disconnect electrical connection to the ignition switch; The first phase of this guide. Close all of the vehicle's doors.
Sometimes you can punch it out but drilling is easier. Using 1/8 drill bit, drill out lock cylinder retaining pin. Twist cap off lock cylinder.
Insert a straightened out paperclip into the slot just to the left of the key cylinder. Find the mounting screws from the ignition switch. I went to the dealer they were not able to locate the correct key even after contacting harley.
Assuming the key didn’t get rotated at all while it was out, installation will consist of lining the key housing’s externals with the ignition switch’s internals. A few cars might have two connections which have to be disconnected. Step 1 drill the center of your ignition cylinder until you reach the end of the key insert.
Replacing ignition switch without a key: Replacing the ignition lock cylinder. Vehicle starting and charging starting system ignition lock service and repair procedures without key without key note:
Unscrew the ignition switch screws or mounting bolts with a socket wrench or screwdriver. How to remove the ignition switch without a key turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder. You can replace your ignition switch in just a few minutes from your driver's seat using a few simple tools.
Remove the screws that are holding the electrical part (the part with the wires) and the mechanical part of the ignition switch together. Please refer to the vehicle's service manual or contact your local ase certified mechanic for assistance with modern ignition systems. Its pretty easy remove the column covering to access the pin you'd push to remove the cylinder with the key on.
To replace your car’s ignition switch without a key, you have to follow the usual steps of replacing the ignition switch except for the method of removing the ignition switch. Remove the sleeves from the steering wheel. I recently bought a 96 ultra that didn’t have keys.
Then you can get to. Insert and remove the ignition key twice (without rotating the ignition lock cylinder). How do i turn my ignition switch on without the key?
Disconnect wires that are found at the rear of the ignition lock cylinder switch. A small knife will help to detach the. The last thing to do is turning the cylinder itself to the left side with a screwdriver.
Unplug the electrical connection that leads to the ignition switch. The old one just won't budge.i have to get it off the lot or my apartment complex will tow it. How do i replace the ignition switch without the original key?
How to replace ignition switch without key. Take the mounting bolts out and check the bolts I lost the original key and i am having difficulty replacing the ignition switch with my screwdriver.
Pull on both the paperclip and the screwdriver to gently slide the switch out of its current position. Put the chisel behind the chrome piece, and hit it with a hammer to break the chrome piece off.